端口扫描工具终极用法 | 至察助安 - 网络安全干货博客
为什么要做c段探测，运营商分配给IDC机房地址时大部分都是连续IP地址，租给客户（渗透目标）时很大概率会分配同C段内IP地址（除非目标就一个IP地址），使用工具扫描可以探测出同段服务。
扫描工具UP主经常用的有三个：
Nmap用法
Nmap（Network Mapper，网络映射器) 是一款开放源代码的网络探测和安全审核的工具。老规矩先放出我最常用的命令组合方式，想了解原理继续看，不想了解直接套用就可以。
|
sudo nmap -v -sS -p8000-9000 -Pn -T4 -A 124.*.8.254 --script http-methods --script-args http.useragent="Mozilla/5.0 (Macintosh; Intel Mac OS X 10.15; rv:87.0) Gecko/20100101 Firefox/87.0"
|
-v 实时输出扫描详情
|
vulab@sechelper:~/masscan$ nmap -v 124.*.8.254
Starting Nmap 7.80 ( https://nmap.org ) at 2022-09-05 04:01 UTC
Initiating Ping Scan at 04:01
Scanning 124.*.8.254 [2 ports]
Completed Ping Scan at 04:01, 0.03s elapsed (1 total hosts)
Initiating Parallel DNS resolution of 1 host. at 04:01
Completed Parallel DNS resolution of 1 host. at 04:01, 0.01s elapsed
Initiating Connect Scan at 04:01
Scanning 124.*.8.254 [1000 ports]
Discovered open port 443/tcp on 124.*.8.254
Discovered open port 22/tcp on 124.*.8.254
Discovered open port 80/tcp on 124.*.8.254
...
|
-A 全面扫描
|
vulab@sechelper:~$ nmap -A 124.*.8.254 # nmap -A 124.*.8.1/24 扫描C段存活端口
Starting Nmap 7.80 ( https://nmap.org ) at 2022-09-04 12:09 UTC
Nmap scan report for 124.*.8.254
Host is up (0.037s latency).
Not shown: 997 filtered ports
PORT STATE SERVICE VERSION
22/tcp open tcpwrapped
|_ssh-hostkey: ERROR: Script execution failed (use -d to debug)
80/tcp open tcpwrapped
|_http-server-header: nginx/1.18.0 (Ubuntu)
443/tcp open tcpwrapped
|_http-server-header: nginx/1.18.0 (Ubuntu)
| ssl-cert: Subject: commonName=navi.sechelper.com
| Subject Alternative Name: DNS:navi.sechelper.com
| Not valid before: 2022-08-27T00:00:00
|_Not valid after: 2023-08-27T23:59:59
| tls-alpn:
|_ http/1.1
| tls-nextprotoneg:
|_ http/1.1
|
-Pn 禁ping扫描，扫描前不ping（不加这个参数Nmap会ping目标地址）
|
vulab@sechelper:~$ nmap -Pn 124.*.8.254
Starting Nmap 7.80 ( https://nmap.org ) at 2022-09-04 13:02 UTC
Nmap scan report for 124.*.8.254
Host is up (0.035s latency).
Not shown: 997 filtered ports
PORT STATE SERVICE
22/tcp open ssh
80/tcp open http
443/tcp open https
Nmap done: 1 IP address (1 host up) scanned in 25.80 seconds
|
-p 指定端口
|
vulab@sechelper:~$ nmap -p22,21,8000-9000 124.*.8.254
Starting Nmap 7.80 ( https://nmap.org ) at 2022-09-04 21:20 CST
Nmap scan report for 124.*.8.254
Host is up (0.0031s latency).
PORT STATE SERVICE
22/tcp open ssh
Nmap done: 1 IP address (1 host up) scanned in 0.34 seconds
|
-sP 使用ping探测主机存活，不扫描端口
|
vulab@sechelper:~$ nmap -sP 192.168.111.1/24
Starting Nmap 7.80 ( https://nmap.org ) at 2022-09-04 12:31 UTC
Nmap scan report for _gateway (192.168.111.2)
Host is up (0.00032s latency).
Nmap scan report for sechelper (192.168.111.133)
Host is up (0.000091s latency).
|
-sS syn扫描/半开放扫描，准确率太低
|
vulab@sechelper:~$ sudo nmap -sS 124.*.8.254
...
Not shown: 979 filtered ports
PORT STATE SERVICE
22/tcp open ssh
80/tcp open http
443/tcp open https
8002/tcp closed teradataordbms
8042/tcp closed fs-agent
8088/tcp closed radan-http
8090/tcp closed opsmessaging
...
Nmap done: 1 IP address (1 host up) scanned in 867.60 seconds
|
-sT 连接扫描，准确率高
|
vulab@sechelper:~$ nmap -sT 124.*.8.254
Starting Nmap 7.80 ( https://nmap.org ) at 2022-09-04 14:14 UTC
Nmap scan report for 124.*.8.254
Host is up (0.037s latency).
Not shown: 997 filtered ports
PORT STATE SERVICE
22/tcp open ssh
80/tcp open http
443/tcp open https
Nmap done: 1 IP address (1 host up) scanned in 14.17 seconds
|
|
状态 |
含义 |
|
open |
端口开着，正在被使用 |
|
closed |
端口已关闭 |
|
filtered |
扫描被阻拦， 无法确定端口是否开放 |
|
unfiltered |
端口可被访问，但不能确定是开放还是关闭 |
表一 Nmap 端口状态表
-T 提升扫描速度，0-5，数值越高速度越快
|
vulab@sechelper:~/masscan$ nmap -A -v -p80 -T4 124.*.8.254
...
PORT STATE SERVICE VERSION
80/tcp open http nginx 1.18.0 (Ubuntu)
| http-methods:
|_ Supported Methods: GET HEAD POST
|_http-server-header: nginx/1.18.0 (Ubuntu)
|_http-title: 403 Forbidden
Service Info: OS: linux; CPE: cpe:/o:linux:linux_kernel
...
|
绕过防火墙/安全设备
Nmap使用默认User-Agent，流量和日志里一览无遗（秃子头上的虱子），不封你封谁。大部分工具默认指纹都已被提取规则，使用的时候注意看下源码或者测试一下。
扫描时指定User-Agent，可以绕过部分安全检测
|
nmap -A -v -p80 124.*.8.254 --script http-methods --script-args http.useragent="Mozilla/5.0 (Macintosh; Intel Mac OS X 10.15; rv:87.0) Gecko/20100101 Firefox/87.0"
|
结果写入文件
原始结果
|
nmap -A -v -p80 -T4 124.*.8.254 -o 4.txt
|
保存为XML格式
|
nmap -A -v -p80 -T4 124.*.8.254 -oX 4.xml
|
参考：
Masscan用法
Masscan是一个互联网规模的端口扫描仪。它可以在5分钟内扫描整个互联网，从一台机器每秒传输1000万个数据包。这是我常用的端口扫描工具，老规矩先放我最常用参数组合，想了解原理继续看，不想了解直接套用。
|
masscan -p80,8000-9000 182.92.106.58 --rate=10000 --banners --source-port 61000 --http-user-agent "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.15; rv:87.0) Gecko/20100101 Firefox/87.0" -Pn
|
编译安装
|
vulab@sechelper:~$ apt install make gcc git -y
vulab@sechelper:~$ git clone https://github.com/robertdavidgraham/masscan.git
vulab@sechelper:~$ cd masscan
vulab@sechelper:~/masscan$ make && make install
...
c -g -ggdb -Wall -O2 -c src/stub-pfring.c -o tmp/stub-pfring.o
cc -g -ggdb -Wall -O2 -c src/syn-cookie.c -o tmp/syn-cookie.o
...
cc -g -ggdb -Wall -O2 -o bin/masscan tmp/crypto-base64.o tmp/crypto-blackrock2.o tmp/event-timeout.o tmp/in-binary.o tmp/in-filter.o tmp/in-report.o tmp/logger.o tmp/main-conf.o tmp/main-dedup.o tmp/main-
...
|
|
vulab@sechelper:~/masscan$ masscan -h # 出现帮助信息表示安装成功
usage:
masscan -p80,8000-8100 10.0.0.0/8 --rate=10000
scan some web ports on 10.x.x.x at 10kpps
masscan --nmap
list those options that are compatible with nmap
masscan -p80 10.0.0.0/8 --banners -oB <filename>
save results of scan in binary format to <filename>
masscan --open --banners --readscan <filename> -oX <savefile>
read binary scan results in <filename> and save them as xml in <savefile>
vulab@sechelper:~/masscan$ masscan --help
MASSCAN is a fast port scanner. The primary input parameters are the
IP addresses/ranges you want to scan, and the port numbers. An example
is the following, which scans the 10.x.x.x network for web servers:
masscan 10.0.0.0/8 -p80
The program auto-detects network interface/adapter settings. If this
fails, you'll have to set these manually. The following is an
example of all the parameters that are needed:
--adapter-ip 192.168.10.123
--adapter-mac 00-11-22-33-44-55
--router-mac 66-55-44-33-22-11
Parameters can be set either via the command-line or config-file. The
names are the same for both. Thus, the above adapter settings would
appear as follows in a configuration file:
adapter-ip = 192.168.10.123
adapter-mac = 00-11-22-33-44-55
router-mac = 66-55-44-33-22-11
All single-dash parameters have a spelled out double-dash equivalent,
so '-p80' is the same as '--ports 80' (or 'ports = 80' in config file).
To use the config file, type:
masscan -c <filename>
To generate a config-file from the current settings, use the --echo
option. This stops the program from actually running, and just echoes
the current configuration instead. This is a useful way to generate
your first config file, or see a list of parameters you didn't know
about. I suggest you try it now:
masscan -p1234 --echo
|
-p 指定端口
|
vulab@sechelper:~/masscan$ sudo masscan -p 80 124.*.8.1/24
Starting masscan 1.3.2 (http://bit.ly/14GZzcT) at 2022-09-05 02:12:22 GMT
Initiating SYN Stealth Scan
Scanning 256 hosts [1 port/host]
Discovered open port 80/tcp on 124.*.8.177
Discovered open port 80/tcp on 124.*.8.39
Discovered open port 80/tcp on 124.*.8.7
Discovered open port 80/tcp on 124.*.8.186
Discovered open port 80/tcp on 124.*.8.13
Discovered open port 80/tcp on 124.*.8.77
Discovered open port 80/tcp on 124.*.8.163
Discovered open port 80/tcp on 124.*.8.133
...
|
–rate=10000 发包频率，数值越大扫描越快，根据自己网络设置，频率太高误报越高
|
vulab@sechelper:~/masscan$ sudo masscan -p 80 124.*.8.1/24 --rate=10000
|
**–banners 指纹信息，配合 –source-port 61000 一起使用 **
Tcp协议连接目标端口时会在系统内分配一个端口与目标通讯，因为有时候从目标返回数据包会被防火墙过滤丢弃，导致masscan无法获取banner信息，所以需要设置一个固定的源端口，方便在防火墙配置白名单不丢弃/拦截此端口数据。
|
vulab@sechelper:~/masscan$ sudo iptables -A INPUT -p tcp --dport 61000 -j DROP
|
|
vulab@sechelper:~/masscan$ sudo masscan -p 80 124.*.8.254 --banners --source-port 61000 --rate=10000
Starting masscan 1.3.2 (http://bit.ly/14GZzcT) at 2022-09-05 03:06:20 GMT
Initiating SYN Stealth Scan
Scanning 1 hosts [1 port/host]
Discovered open port 80/tcp on 124.*.8.254
Banner on port 80/tcp on 124.*.8.254: [http.server] nginx/1.18.0 (Ubuntu)
Banner on port 80/tcp on 124.*.8.254: [title] 403 Forbidden
Banner on port 80/tcp on 124.*.8.254: [http] HTTP/1.1 403 Forbidden\x0d\x0aServer: nginx/1.18.0 (Ubuntu)\x0d\x0aDate: Mon, 05 Sep 2022 03:06:22 GMT\x0d\x0aContent-Type: text/html\x0d\x0aContent-Length: 162\x0d\x0aConnection: close\x0d\x0a\x0d
|
绕过安全检测
在源码masscan/src/proto-http.c中预定义的User-Agent各大厂商肯定已经提取指纹规则，还在使用默认User-Agent不封你封谁，大部分工具默认指纹都已被提取规则，使用的时候注意看下源码或者测试一下。
服务器日志里看的清清楚楚，溯源一抓一个准。
扫描时指定User-Agent，可以绕过部分安全检测
|
vulab@sechelper:~/masscan$ sudo masscan -p 80 124.*.8.254 --banners --source-port 61000 --rate=10000 --http-user-agent "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.15; rv:87.0) Gecko/20100101 Firefox/87.0"
Starting masscan 1.3.2 (http://bit.ly/14GZzcT) at 2022-09-05 03:15:14 GMT
Initiating SYN Stealth Scan
Scanning 1 hosts [1 port/host]
Discovered open port 80/tcp on 124.*.8.254
Banner on port 80/tcp on 124.*.8.254: [http.server] nginx/1.18.0 (Ubuntu)
Banner on port 80/tcp on 124.*.8.254: [title] 403 Forbidden
Banner on port 80/tcp on 124.*.8.254: [http] HTTP/1.1 403 Forbidden\x0d\x0aServer: nginx/1.18.0 (Ubuntu)\x0d\x0aDate: Mon, 05 Sep 2022 03:15:16 GMT\x0d\x0aContent-Type: text/html\x0d\x0aContent-Length: 162\x0d\x0aConnection: close\x0d\x0a\x0d
|
-Pn 扫描前不PING，直接开扫
|
vulab@sechelper:~/masscan$ sudo masscan -p 80 124.*.8.254 --banners --source-port 61000 --rate=10000 --http-user-agent "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.15; rv:87.0) Gecko/20100101 Firefox/87.0" -Pn
|
结果写入文件
-oJ 保存为Json格式
|
sudo masscan -p 80 124.*.8.254 --banners --source-port 61000 --rate=10000 --http-user-agent "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.15; rv:87.0) Gecko/20100101 Firefox/87.0" -oJ 22090501.json
|
-oX 保存为XML格式
|
sudo masscan -p 80 124.*.8.254 --banners --source-port 61000 --rate=10000 --http-user-agent "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.15; rv:87.0) Gecko/20100101 Firefox/87.0" -oJ 22090501.xml
|
重定向输出，保存为原始格式
|
sudo masscan -p 80 124.*.8.254 --banners --source-port 61000 --rate=10000 --http-user-agent "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.15; rv:87.0) Gecko/20100101 Firefox/87.0" > 22090501.txt
|
Zmap
ZMap是一种快速的单包网络扫描仪，专为互联网范围内的网络调查而设计。在具有千兆以太网连接的典型台式计算机上，ZMap能够在45分钟内扫描整个公共IPv4地址空间。
编译安装
|
sudo apt-get install build-essential cmake libgmp3-dev gengetopt libpcap-dev flex byacc libjson-c-dev pkg-config libunistring-dev git -y
git clone https://github.com/zmap/zmap.git
cmake .
make -j4
|
老规矩先放我最常用参数组合，想了解原理继续看，不想了解直接套用。
|
sudo zmap -B 1M -p80 --source-port=61000 124.*.8.1/24 -o 22090501.txt
|
参数解释
-B 扫描速率最大带宽
-p 端口号，单一
-o 输出到文件
zgrab
ZGrab是一种快速、模块化的应用层网络扫描仪，用于完成大型互联网范围的调查。ZGrab配合ZMap一起使用。
老规矩先放我最常用参数组合，想了解原理继续看，不想了解直接套用。
|
./zgrab2 http -p 80 -f 22090501.txt -o 22090502.json --user-agent="Mozilla/5.0 (Macintosh; Intel Mac OS X 10_12_2) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/55.0.2883.95 Safari/537.36"
|
zmap和zgrab2联合使用
|
sudo zmap -B 1M -p80 --source-port=61000 124.*.8.1/24|ztee 22090503.csv| ./zgrab2 http -p80 --user-agent="Mozilla/5.0 (Macintosh; Intel Mac OS X 10_12_2) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/55.0.2883.95 Safari/537.36" -o 22090504.json
|
编译安装
|
sudo apt install golang-go
git clone https://github.com/zmap/zgrab2.git
cd zgrab2
make
|
使用刚才ZMap扫描结果，探测http服务的Banner信息
|
./zgrab2 http -f 22090501.txt -o 22090502.json
|
http端口默认是80，可以自行指定非默认端口的http服务
|
./zgrab2 http -p 8080 -f 22090501.txt -o 22090502.json
|
查看模块的帮助信息，例如查看http这个模块有哪些可设置参数
|
vulab@sechelper:~/zgrab2$ ./zgrab2 http -h
Usage:
zgrab2 [OPTIONS] http [http-OPTIONS]
...
[http command options]
-p, --port= Specify port to grab on (default: 80)
...
--user-agent= Set a custom user agent (default: Mozilla/5.0 zgrab/0.x)
...
|
绕过安全检测
查看服务器日志User-Agent一眼看出是zgrab在探测，默认的User-Agent是Mozilla/5.0 zgrab/0.x
vulab@sechelper:~/zgrab2$ ./zgrab2 http -p80 --user-agent="Mozilla/5.0 (Macintosh; Intel Mac OS X 10_12_2) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/55.0.2883.95 Safari/537.36" -f 22090501.txt
关注 至察助安 ，专注网络安全优质知识分享，无优质，不分享。
,
免责声明：本文仅代表文章作者的个人观点，与本站无关。其原创性、真实性以及文中陈述文字和内容未经本站证实，对本文以及其中全部或者部分内容文字的真实性、完整性和原创性本站不作任何保证或承诺，请读者仅作参考，并自行核实相关内容。文章投诉邮箱：anhduc.ph@yahoo.com
